What is Fine Grinding?

Fine grinding is a batch-mode abrasive machining process that combines the speed and aggressiveness of super abrasive wheels with accuracy of lapping kinematics to produce flat and parallel work piece surfaces.
The fine grinding cutting tool consists of an upper and lower wheel composed of diamond or cubic boron nitride (CBN) with different bond types (vitrified bond, resin bond or metal bond) and act as the support plates for the work pieces.
The machine tool has evolved from the vertical double-wheel lapping machine design with a planetary work drive system, also known as “lapping kinematics”.
In place of lapping wheels, grinding wheels are fitted and cooled through labyrinth in the working wheels and a coolant fed through holes in the upper wheel.
Since fine grinding requires higher forces and uses higher cutting speeds, motors, gears and the rigidity of the machines are much stronger than lapping machines.
Work pieces are guided between the upper and lower working wheel in an epicyclical path as defined by inner and outer pin ring, upper and lower working wheel, speeds and directions, while material removal takes place simultaneously on both sides.

Why use Fine Grinding?

General

Accuracy results, previously only achieved by lapping
The pellet structure allows a layout of the fine grinding medium, corresponding to the kinematics conditions
Long and constant process cycles without dressing processes
The space between the pellets allows a high flow rate of the coolant
Very good chip flow without temperature problems
High process quality, consistent repeatability of achieved values
Also large surface work pieces can be machined
Fine grinding can use batch processing
Work pieces are loosely held in carriers and therefore machined stress free (without distortion - especially for machining of thin or delicate parts)
Work pieces of different shapes could be machined (i.e. round, rectangular or irregular; full surface or with cut-outs)
Fine grinding is easily automated

Fast

High removal rate using super abrasive diamond and CBN (3 – 20 times faster than lapping)
Possible saving of pre-machining steps
Fine grinding benefits from long intervals between resharpening
Fine grinding has high flexibility
Automated solutions

Clean

Fine grinding benefits from the recycling of coolant
Tremendous less waste than with lapping
Minimal work piece cleaning necessary
Fine grinding reduces downtime
Cleaning of work pieces without problems by rinsing; in comparison to lapping ultrasonic or chemical cleaning is not necessary

Economic

Fine grinding has a high removal rate (reduces capital costs and personnel expenditure)
Low wheel wear and long life time of the grinding wheels (reduces the tool costs)
Low waste disposal costs (reduces the current running costs)
Low work piece cleaning costs (reduces the current running costs)
Fine grinding may have a possible saving of additional machining steps
Easy wheel maintenance _low tool manufacturing costs by using a “Standard-Pellet-Form”

Fine Grinding

Performed with super abrasive (diamond or cubic boron nitride - CBN) wheels
Stock removal caused by micro grooving / -cutting
Fine-ground surface has cross-hatched marks
Coolant is recycled
Fine-ground parts are coated only with a thin layer of coolant and therefore only minimal workpiece cleaning is necessary
Wheel speeds are typically 2 – 15 m/s
3 – 20 times faster than lapping (removal rate)

Lapping

Lapping is a working process, during which workpiece and tool slide over one another on a loosely applied medium (lapping compound) and are subject to continually changing direction of rotation.
Stock removal caused by rolling and sliding action of abrasive grains
Lapped surface is dull and crater-like
Material and lapping compound are not recycled
Lapped parts are contaminated with lapping compound and require cleaning
Lapping speeds are generally limited to < 1 m/s

Definition of the Tooling Methods

Lapping flat parts – single or double-side) is the abrasive machining process for removing material using a loose abrasive in a liquid mixture (known as a slurry) at low speeds.
Loose abrasive is moving over the surface under pressure (fig. 1), will knead, abrade, chip or scrape away the surface of the workpiece (fig. 2). By exceeding the bending strength the material breaks out.
Fine Grinding (flat parts – single or double-side) is the abrasive machining process for removing material using a bonded Superabrasive wheel at low speed with a liquid to keep the part cool. The fixed grain of a geometrically indefinable cutting shape acts like a plow (fig. 3) and material is removed by micro-grooving /-cutting (fig. 4). The chip formation occurs by exceeding the shearing strength.

Fine Grinding vs Lapping

Kinematics of the Fine Grinding Process

Fine Grinding generally follows the same kinematic principle as lapping. The fine grinding workpieces are held in carriers which are driven to describe a planetary motion covering the full surface of the Fine Grinding wheel. The drive mechanism consists of an inner and outer pin ring. The outer ring is generally fixed while the inner ring rotates in either the opposing or the same direction as the lower working wheel to create a series of epicyclic rotations.

Why use Lapmaster Fine Grinding Machines and Systems?

Lapmaster fine grinding machines and systems offers a complete line of products for all fine grinding requirements. We can offer fully integrated systems and machines for high volume fine grinding and industrial production applications and equipment for low volume job shop applications. Lapmaster also offers used fine grinding (rebuilt and refurbished) and upgrade services for existing fine grinding machines. We provide our customers with fully engineered complete custom solutions and offer a full line of accessories and consumables in addition to comprehensive training and repair services.

Our extensive line of fine grinding machines / systems for both medium to large-scale serial production as well as small batch production; these systems can be made to be manually operated or fully automated. With innovation and customer service as our main objectives, Lapmaster continuously researching and developing new technology and fine grinding machinery. By consistently staying on top of the latest developments on the market, we ensure that our customers are provided with the most state-of-the-art production and control.